Panasonic Split & Duct AC Error Codes (Legend Series Included)

 

Panasonic Inverter Air Conditioner Error Codes and Diagnostic Guide

Panasonic inverter air conditioners are known for their efficiency and smart technology, but like all machines, they may encounter issues over time. This guide provides a detailed list of error codes for Panasonic inverter models—including split systems, floor-standing units, and concealed duct types (Legend series)—along with their corresponding causes and diagnostic steps.

---

🔍 How to Diagnose Faults on Panasonic Inverter AC Units

1. When a fault occurs, the "Timer" light will blink orange.

2. Use the Panasonic inverter remote control to access diagnostic mode.

3. Use a small stick (or the tip of the remote) to press and hold the "Check" button for 5 seconds.

4. The error code will appear on the remote display.

5. Press the Temperature Up/Down buttons to scroll through the codes. When the displayed code matches the detected error, the indoor unit will emit a continuous "beep-beep-beep".

---

⚠️ Common Panasonic Inverter Air Conditioner Error Codes

H00 – No Abnormality Detected

✅ Everything is functioning normally.

---

H11 – Communication Error Between Indoor and Outdoor Units

Issue:

• Communication failure within 15 seconds of startup.
  Causes:

• Incorrect wiring between indoor and outdoor units.

• Disconnected or damaged communication cable.

• Faulty indoor or outdoor PCB.

---

H14 – Indoor Room Temperature Sensor Error

Issue:

• Detected indoor temperature < -50°C or > 149°C.
  Causes:

• Shorted or open room temperature sensor.

• Faulty PCB terminal (CN-TH) or incorrect wiring.

---

H15 – Compressor Temperature Sensor Error

Issue:

• Detected temperature < -16°C or > 200°C within 5 minutes of compressor startup.
  Causes:

• Sensor short/open circuit.

• Faulty CN-TH terminal or miswiring.

---

H16 – Outdoor Current Transformer (CT) Error

Issue:

• Operating current < 2A for 20 seconds (detected 3 times).
  Causes:

• Refrigerant leak.

• Faulty outdoor PCB or CT sensor.

• Compressor running unloaded.

---

H19 – Indoor Fan Motor Locked

Issue:

• Detected motor current fault 7 times.
  Causes:

• Faulty fan motor or wiring.

• PCB or CN-TH terminal issue.

---

H23 – Indoor Heat Exchanger Sensor Error

Causes:

• Sensor short/open circuit.

• CN-TH terminal issue.

---

H27 / H28 – Outdoor Ambient / Pipe Temperature Sensor Error

Issue:

• Detected temperature < -50°C or > 150°C / < -58°C or > 107°C.
  Causes:

• Sensor failure or wiring issues.

---

H97 – Outdoor Fan Motor Error

Issue:

• Fan speed abnormality detected twice within 10 minutes.
  Causes:

• Motor failure, wiring error, or PCB fault.

---

H98 – Indoor Heat Rise Abnormality

Causes:

• Dirty air filter.

• Weak airflow or fan failure.

• Improper valve operation or restricted piping.

• Air in the refrigerant circuit.

---

H99 – Indoor Anti-Freeze Control Error

Issue:

• Coil temperature < 0°C for 6 minutes.
  Causes:

• Dirty filters.

• Low refrigerant charge.

• Piping deformity or sensor drift.

---

F11 – Heating/Cooling Mode Switching Error

Issue:

• Evaporator temp < -7°C for 3 mins after 25 mins of heating mode (repeated 4 times).
  Causes:

• Faulty 4-way valve.

• CN-HOT terminal loose connection.

---

F16 – Horizontal Airflow Louver Error

---

F90 – PFC Circuit Protection

Issue:

• Overvoltage detected >353.3V (4 times within 20 mins).
  Causes:

• Faulty reactor or poor connection.

• Unbalanced compressor winding resistance.

• Outdoor PCB malfunction.

---

F91 – Refrigerant Circuit Error

Issue:

• Temperature difference between indoor coil and room air too small.
  Causes:

• Refrigerant leakage.

• Closed expansion valve.

• Poor compressor performance.

---

F93 – Compressor Speed Control Failure

Issue:

• RPM feedback error or loss (detected 4 times).
  Causes:

• Outdoor PCB fault.

• Compressor malfunction.

• Valve not fully opened.

---

F95 – Cooling Overpressure Protection

Issue:

• Pipe temperature > 62°C detected 4 times in 20 minutes.
  Causes:

• Dirty outdoor condenser.

• Excess refrigerant.

• Poor airflow or obstruction.

---

F96 – IPM Module Overheat

Issue:

• Detected 4 times in 30 minutes, triggers system shutdown.
  Causes:

• Dirty condenser.

• High refrigerant volume.

• Blocked ventilation or faulty IPM.

• Compressor seizure or outdoor fan lock.

---

🧰 Pro Tip: Use Proper Tools for Fast Disassembly

Using high-quality tools will ensure safety and speed during air conditioner servicing. Always have reliable tubing cutters, leak detectors, and multimeters on hand.

---

✅ Conclusion

Understanding the error codes of Panasonic inverter AC units can greatly assist in troubleshooting and timely repairs. Always ensure proper wiring, clean filters, and correct refrigerant charge levels to prevent most of these issues. For persistent problems, consult a certified HVAC technician.

Panasonic inverter air conditioner error codes

Panasonic AC troubleshooting

AC diagnostic guide

HVAC repair tips

air conditioner sensor error

Panasonic fault code H11 H98 F95

inverter AC repair

split AC maintenance

Panasonic Legend series AC

air conditioning problems and solutions